Anatomical terms of movement are used to describe the actions of muscles upon the skeleton. Muscles contract to produce movement at joints, and the subsequent movements can be precisely described using this terminology. Abduction and adduction are two terms that are used to describe movements towards or away from the midline of the body. Source: API RP 16Q, Recommended Practice for Design, Selection, Operation and Maintenance of Marine Drilling Riser Systems, First Edition, November 1993 (Reaffirmed August 2001). Global Standards

Marfan syndrome: A condition that affects your connective tissue. A defect in the gene responsible for building fibrillin and elastic fibers — a major part of your connective tissue — causes this syndrome. Source: API RP 17G, Recommended Practice for Completion/Workover Risers, Second Edition, July 2006 (Reaffirmed April 2011). Global Standards Source: API Specification 16Q, Design, Selection, Operation, and Maintenance of Marine Drilling Riser Systems, Second Edition, April 2017. Global Standards Do I need to replace the entire section?’ The answer is no, so long as you are able to weld in situa (being able to weld or clamp the flexi whilst it’s on the vehicle) or are able to remove the factory exhaust section off the vehicle to be able to carry the work out on a work bench. Low-FODMAP diet: A group of five sugars found in certain foods is removed from your diet. These sugars are lactose, fructose, fructans, galactans and polyols. FODMAP stands for fermentable, oligosaccharides, disaccharides, monosaccharides and polyols.On some vehicles, manufacturers place the flexi section immediately before/after a catalytic converter or a DPF. These particular flexibles have to be replaced with a WELD ON flexi as there is no pipe to clamp on to. However, if your car has a flexible with enough straight pipe on each side, you can easily cut the old broken flexible and replace it with one of our CLAMP ON flexi joints. Again, keeping the elbow and shoulder still, flip your hand onto its front, palm down. This is the prone position, and so this movement is named pronation. In most people, hypermobility doesn’t cause any pain or medical issues. However, for some people, hypermobility causes joint pain, joint and ligament injuries, tiredness (fatigue), bowel issues and other symptoms. Joint hypermobility syndrome is most common in children and young people. It affects people assigned female at birth (AFAB) and people of Asian and Afro-Caribbean descent more often. It usually gets better with age. Is joint hypermobility syndrome the same as Ehlers-Danlos syndrome?

Inversion involves the movement of the sole towards the median plane - so that the sole faces in a medial direction. Device(s) installed between the bottom of the diverter and the telescopic joint (upper flex or ball joint), in the top section of the LMRP (lower flex or ball joint), or under a keel joint (intermediate flex or ball joint, if used), to permit relative angular movement of the riser and reduce stresses due to vessel motion and environmental forces. It is sometimes talked about as a circular motion, but is more accurately conical due to the 'cone' formed by the moving limb. Protraction and RetractionLaminated metal and elastomer assembly, having a central through-passage equal to or greater in diameter than the interfacing pipe or tubing bore, that is positioned in the riser string to reduce the local bending stresses.

Elevation refers to movement in a superior direction (e.g. shoulder shrug), depression refers to movement in an inferior direction. Lactose-free diet: Lactose is removed from your diet to see if you’re intolerant to dairy products.

Inversion and Eversion

caption id="attachment_10384" align="aligncenter" width="782"] Fig 2 - Adduction, abduction and rotation.[/caption]

Flexion and extension are movements that occur in the sagittal plane. They refer to increasing and decreasing the angle between two body parts: In fingers and toes, the midline used is not the midline of the body, but of the hand and foot respectively. Therefore, abducting the fingers spreads them out. Ehase-Flex company located in Hangzhou, near Shanghai and Ningbo port, is one of the most famous brands in metal flexible joint and expansion joint.We founded our factory in China mainland in 2006. We are specialized in manufacturing flexible joint, expansion joint, flexible sprinkler hose, flexible tube, gas connector, rubber joint and spring mount. Our company had obtained the quality control system ISO9001. Our products are FM, UL, CCC, CSA, SGS approved and 100% tested before delivery. With high quality our products are widely used in many fields such as petroleum, chemical, semiconductor, electronics, machinery, electric power, ship building, nuclear energy, and have got highly recognized among customers both domestic and overseas. We have customers such as SAMSUNG, LG, MIXC MALL, Hyatt hotel, Marriott Hotel.A steel and elastomer assembly having central through-passage equal to or greater in diameter than the riser bore that may be positioned in the riser string to reduce local bending stresses.